Turbo install and motor rebuild has begun...................

[JustinG]

Well it has begun........
Howell 2.0L, 8.6:1 bottom end long rod kit $999 <!-- w --><a class="postlink" href="http://www.howellautomotive.com">www.howellautomotive.com</a><!-- w -->
Garrett T3/T04e 50 trim $720( + a free t-shirt ) <!-- w --><a class="postlink" href="http://www.cheapturbo.com">www.cheapturbo.com</a><!-- w -->
Custom Manifold $80 (only cost was pieces to build mani)
Ebay intercooler 24x12x2.75 $280
Greddy RS BOV $175? <!-- w --><a class="postlink" href="http://www.extremePSI.com">www.extremePSI.com</a><!-- w -->
Tial 38mm WG with 7psi spring $275? <!-- w --><a class="postlink" href="http://www.extremePSI.com">www.extremePSI.com</a><!-- w -->
Aeromotive 1:1 FPR <!-- w --><a class="postlink" href="http://www.summitracing.com">www.summitracing.com</a><!-- w -->
Walbor 255LPH $95 <!-- w --><a class="postlink" href="http://www.extremePSI.com">www.extremePSI.com</a><!-- w -->
RC engineering 550cc Low Imp injectors $69 a piece <!-- w --><a class="postlink" href="http://www.horsepowerfreaks.com">www.horsepowerfreaks.com</a><!-- w -->
Spec stage 3 clutch $350? <!-- w --><a class="postlink" href="http://www.horsepowerfreaks.com">www.horsepowerfreaks.com</a><!-- w -->
PLX m300 wideband $313 <!-- w --><a class="postlink" href="http://www.horsepowerfreaks.com">www.horsepowerfreaks.com</a><!-- w -->
MSnS(420A/neon w/ 3 bar map) $299 <!-- w --><a class="postlink" href="http://www.rsautosport.com">www.rsautosport.com</a><!-- w -->
Energy suspension motor mounts $20 <!-- w --><a class="postlink" href="http://www.horsepowerfreaks.com">www.horsepowerfreaks.com</a><!-- w -->
Autometer Phantom: Boost, EGT, Oil Pressure $225 approx <!-- w --><a class="postlink" href="http://www.summitracing.com">www.summitracing.com</a><!-- w -->
Numerous SS lines and -AN fitting <!-- w --><a class="postlink" href="http://www.summitracing.com">www.summitracing.com</a><!-- w -->
Custom pieced together 3" turbo back exhaust $unknown
IC piping $unknown
Greddy TT $70 <!-- w --><a class="postlink" href="http://www.ebay.com">www.ebay.com</a><!-- w -->
EBAY MBC $15 <!-- w --><a class="postlink" href="http://www.ebay.com">www.ebay.com</a><!-- w -->

Start working on monday at a drag shop in Fluvanna, VA on monday called Marty's.......wish me luck

mmmmmmmmmmm carbon buildup

Oil feed and sending unit all rigged up

Gauges and wideband

TURBOOOOOOOOOOOOOO

Custom Mani, not fully welded, turbo flange is just tacked on

JE 8.8:1 pistons (not pictured eagle forged long rods)

[.RJ]

$175 for a BOV?

I sure hope its loud!

[JustinG]

loud and bling.....but you prob wont be able to hear it if i do an O2 dump, havent decided if i am or not due to daily driving ive heard it can become a bitch.
Heres a clip of the Type S ive been told the sound similar.... <!-- m --><a class="postlink" href="http://www.935motorsports.com/media/mark7m001.mp3">http://www.935motorsports.com/media/mark7m001.mp3</a><!-- m -->
And the O2 dump....
<!-- m --><a class="postlink" href="http://www.twingles.com/ideck/mpg/dregrowl.avi">http://www.twingles.com/ideck/mpg/dregrowl.avi</a><!-- m -->

[PDenbigh]

Congrats man, and good luck! There will be times you get really frustrated but keep plugging. Also, take your time increasing boost and make sure all your ducks are in a row before doing so. I started at 7psi, am now at 11 and I have some bugs to work out.

Your car is going to be a blast!

Pete

[white_2kgt]

also, make sure your turbo is put together correctly...

--chad

[PDenbigh]

also, make sure your turbo is put together correctly...

--chad

Ha HA!

(Mine wasn't, thrust berring and compressor wheel trashed, and thus why the XR hasn't been proweling the streets this week!...)

[JohnC]

Start working on monday at a drag shop in Fluvanna, VA on monday called Marty's.......wish me luck

Nice. That's right off of 15 (between Zion X-roads and Palmyra), with all the trailers in front of it? I'll have to stop by sometime and check it out.

[Andy]

What are you using for management?

[JustinG]

im using Megasquirt and spark, and the turbo is built correctly, fully balanced, stage 3 wheel, 360 degree thrust......blah blah blah. Yeah stop on by, oh and another thing. If anyone is looking for roll cages, the place im working build 6 point cages for 650 bucks.........

[ScottyB]

nice grocery list you got there. good luck with the buildup

[ViPER1313]

also, make sure your turbo is put together correctly...

--chad

Ha HA!

(Mine wasn't, thrust berring and compressor wheel trashed, and thus why the XR hasn't been proweling the streets this week!...)

So that was why you had death smoke :roll: .

[Nis01]

Money... :lol: Grats on the new toys.

[JustinG]

well the install is on hold for now....waiting on some gaskets as well as a few more SS lines, also gotta finish welding up the exhaust mani and weld the bung onto the oil pan for the oil return from the turbo....that is all for now

[KPWSerpiente]

Don't be a pussy Justin. Do it the DSM way...20+ psi.

-T

[JustinG]

give it time, 20 PSI will come soon enough gotta order a heavier wastegate spring and get her tuned first though........anyone wanna help with tuning my MSnS???

[KPWSerpiente]

You might want to change that to...anyone who hasn't blown up a motor yet, want to help me tune my ms.

-T

[JustinG]

good call, painted the motor today, and yes i know how long its gonna last, but it will look pimp for a little while.....

[BLINGMW]

cool! :thumbup: So, what's this for? A street machine? You drag race?

[JustinG]

well honestly a street machine, may drag it a few times. But really its just me compensating for my dramatically small penis.....

[lillitnn92]

well honestly a street machine, may drag it a few times. But really its just me compensating for my dramatically small penis.....

hmmmm, maybe that's why i still have a Ranger, no need to compensate

what are you expecting HP wise?