+- Madison Motorsports (https://forum.mmsports.org)
+-- Forum: Technical (https://forum.mmsports.org/forumdisplay.php?fid=4)
+--- Forum: Technical Discussion (https://forum.mmsports.org/forumdisplay.php?fid=11)
+--- Thread: Turbo install and motor rebuild has begun................... (/showthread.php?tid=2259)
Pages:
1
2
Turbo install and motor rebuild has begun................... - JustinG - 05-13-2005
Well it has begun........
Howell 2.0L, 8.6:1 bottom end long rod kit $999 <!-- w --><a class="postlink" href="http://www.howellautomotive.com">www.howellautomotive.com</a><!-- w -->
Garrett T3/T04e 50 trim $720( + a free t-shirt ) <!-- w --><a class="postlink" href="http://www.cheapturbo.com">www.cheapturbo.com</a><!-- w -->
Custom Manifold $80 (only cost was pieces to build mani)
Ebay intercooler 24x12x2.75 $280
Greddy RS BOV $175? <!-- w --><a class="postlink" href="http://www.extremePSI.com">www.extremePSI.com</a><!-- w -->
Tial 38mm WG with 7psi spring $275? <!-- w --><a class="postlink" href="http://www.extremePSI.com">www.extremePSI.com</a><!-- w -->
Aeromotive 1:1 FPR <!-- w --><a class="postlink" href="http://www.summitracing.com">www.summitracing.com</a><!-- w -->
Walbor 255LPH $95 <!-- w --><a class="postlink" href="http://www.extremePSI.com">www.extremePSI.com</a><!-- w -->
RC engineering 550cc Low Imp injectors $69 a piece <!-- w --><a class="postlink" href="http://www.horsepowerfreaks.com">www.horsepowerfreaks.com</a><!-- w -->
Spec stage 3 clutch $350? <!-- w --><a class="postlink" href="http://www.horsepowerfreaks.com">www.horsepowerfreaks.com</a><!-- w -->
PLX m300 wideband $313 <!-- w --><a class="postlink" href="http://www.horsepowerfreaks.com">www.horsepowerfreaks.com</a><!-- w -->
MSnS(420A/neon w/ 3 bar map) $299 <!-- w --><a class="postlink" href="http://www.rsautosport.com">www.rsautosport.com</a><!-- w -->
Energy suspension motor mounts $20 <!-- w --><a class="postlink" href="http://www.horsepowerfreaks.com">www.horsepowerfreaks.com</a><!-- w -->
Autometer Phantom: Boost, EGT, Oil Pressure $225 approx <!-- w --><a class="postlink" href="http://www.summitracing.com">www.summitracing.com</a><!-- w -->
Numerous SS lines and -AN fitting <!-- w --><a class="postlink" href="http://www.summitracing.com">www.summitracing.com</a><!-- w -->
Custom pieced together 3" turbo back exhaust $unknown
IC piping $unknown
Greddy TT $70 <!-- w --><a class="postlink" href="http://www.ebay.com">www.ebay.com</a><!-- w -->
EBAY MBC $15 <!-- w --><a class="postlink" href="http://www.ebay.com">www.ebay.com</a><!-- w -->
Start working on monday at a drag shop in Fluvanna, VA on monday called Marty's.......wish me luck
mmmmmmmmmmm carbon buildup
![[Image: 470851_62.jpg]](http://memimage.cardomain.net/member_images/2/web/470000-470999/470851_62.jpg)
Oil feed and sending unit all rigged up
![[Image: 470851_63.jpg]](http://memimage.cardomain.net/member_images/2/web/470000-470999/470851_63.jpg)
Gauges and wideband
![[Image: 470851_64.jpg]](http://memimage.cardomain.net/member_images/2/web/470000-470999/470851_64.jpg)
TURBOOOOOOOOOOOOOO
![[Image: 470851_65.jpg]](http://memimage.cardomain.net/member_images/2/web/470000-470999/470851_65.jpg)
Custom Mani, not fully welded, turbo flange is just tacked on
![[Image: 470851_66.jpg]](http://memimage.cardomain.net/member_images/2/web/470000-470999/470851_66.jpg)
JE 8.8:1 pistons (not pictured eagle forged long rods)
![[Image: 470851_67.jpg]](http://memimage.cardomain.net/member_images/2/web/470000-470999/470851_67.jpg)
- .RJ - 05-13-2005
$175 for a BOV?
I sure hope its loud!
- JustinG - 05-13-2005
loud and bling.....but you prob wont be able to hear it if i do an O2 dump, havent decided if i am or not due to daily driving ive heard it can become a bitch.
Heres a clip of the Type S ive been told the sound similar.... <!-- m --><a class="postlink" href="http://www.935motorsports.com/media/mark7m001.mp3">http://www.935motorsports.com/media/mark7m001.mp3</a><!-- m -->
And the O2 dump....
<!-- m --><a class="postlink" href="http://www.twingles.com/ideck/mpg/dregrowl.avi">http://www.twingles.com/ideck/mpg/dregrowl.avi</a><!-- m -->
- PDenbigh - 05-13-2005
Congrats man, and good luck! There will be times you get really frustrated but keep plugging. Also, take your time increasing boost and make sure all your ducks are in a row before doing so. I started at 7psi, am now at 11 and I have some bugs to work out.
Your car is going to be a blast!
Pete
- white_2kgt - 05-13-2005
also, make sure your turbo is put together correctly...
--chad
- PDenbigh - 05-13-2005
white_2kgt Wrote:also, make sure your turbo is put together correctly...
--chad
Ha HA!
(Mine wasn't, thrust berring and compressor wheel trashed, and thus why the XR hasn't been proweling the streets this week!...)
Re: Turbo install and motor rebuild has begun............... - JohnC - 05-13-2005
white97dsm Wrote:Start working on monday at a drag shop in Fluvanna, VA on monday called Marty's.......wish me luck
Nice. That's right off of 15 (between Zion X-roads and Palmyra), with all the trailers in front of it? I'll have to stop by sometime and check it out.
- Andy - 05-13-2005
What are you using for management?
- JustinG - 05-13-2005
im using Megasquirt and spark, and the turbo is built correctly, fully balanced, stage 3 wheel, 360 degree thrust......blah blah blah. Yeah stop on by, oh and another thing. If anyone is looking for roll cages, the place im working build 6 point cages for 650 bucks.........
- ScottyB - 05-13-2005
nice grocery list you got there. good luck with the buildup
- ViPER1313 - 05-13-2005
PDenbigh Wrote:white_2kgt Wrote:also, make sure your turbo is put together correctly...
--chad
Ha HA!
(Mine wasn't, thrust berring and compressor wheel trashed, and thus why the XR hasn't been proweling the streets this week!...)
So that was why you had death smoke :roll: .
- Nis01 - 05-13-2005
Money... :lol: Grats on the new toys.
- JustinG - 05-14-2005
well the install is on hold for now....waiting on some gaskets as well as a few more SS lines, also gotta finish welding up the exhaust mani and weld the bung onto the oil pan for the oil return from the turbo....that is all for now
- KPWSerpiente - 05-15-2005
Don't be a pussy Justin. Do it the DSM way...20+ psi.
-T
- JustinG - 05-15-2005
give it time, 20 PSI will come soon enough
gotta order a heavier wastegate spring and get her tuned first though........anyone wanna help with tuning my MSnS???
- KPWSerpiente - 05-15-2005
You might want to change that to...anyone who hasn't blown up a motor yet, want to help me tune my ms.
-T
- JustinG - 05-16-2005
good call, painted the motor today, and yes i know how long its gonna last, but it will look pimp for a little while.....
![[Image: 470851_68.jpg]](http://memimage.cardomain.net/member_images/2/web/470000-470999/470851_68.jpg)
![[Image: 470851_69.jpg]](http://memimage.cardomain.net/member_images/2/web/470000-470999/470851_69.jpg)
- BLINGMW - 05-16-2005
cool! :thumbup: So, what's this for? A street machine? You drag race?
- JustinG - 05-16-2005
well honestly a street machine, may drag it a few times. But really its just me compensating for my dramatically small penis.....
- lillitnn92 - 05-16-2005
white97dsm Wrote:well honestly a street machine, may drag it a few times. But really its just me compensating for my dramatically small penis.....
hmmmm, maybe that's why i still have a Ranger, no need to compensate
what are you expecting HP wise?