+- Madison Motorsports (https://forum.mmsports.org)
+-- Forum: Madison Motorsports (https://forum.mmsports.org/forumdisplay.php?fid=3)
+--- Forum: Lounge (https://forum.mmsports.org/forumdisplay.php?fid=6)
+--- Thread: Dyno Pull Pool (/showthread.php?tid=755)
- Eclipsor - 07-30-2004
ButtDyno Wrote:Traction, power, drivetrain reliability: pick two... what do you think your traction oriented mods are going to do to the transmission/drivetrain parts?
More specifically: tires, clutch, and drivetrain parts. There's always a tradeoff.
He can rest assured that his traction mods won't hurt his driveline, unless he's got some SERIOUS wheel hop.
Chris
- KPWSerpiente - 08-03-2004
I'm not worried at hurting the drivetrain. Breaking an axle is always possible but I expect the clutch to take most of the abuse...that is what it is there for.
Tomorrow is the moment of truth, results will be posted early afternoon.
-T
- Dave - 08-03-2004
don't waste your time with the MXs. Thats what I have on the rear of the IV right now. I hydroplane constantly in downpours (regardless of interstate of backroad) and it makes for some scary driving. They are pretty good other than that and definitely cheaper than some alternatives. So far, wear has been really good (for me at least) and they aren't particularly loud or obnoxious. I still would get some Falkens if I could for this car.
- KPWSerpiente - 08-03-2004
Ok here is how it rolled.
Woke up at 9:00 am so I could take a final check on the car. Switched from my rims with 0 tread khumo 712's to two steelie rims with 75% tread khumo 712's. They are what I've been running at the track so I thought I'd use them here now.
Picked up my crew chief dan and my friend's laptop. Arrived at MachV/Ultimate Performance at 10:30. I was missfiring at wot on the way over so I asked about some new plugs. They didn't have any one heat range or two heat ranges colder...just stock. So I took the plugs out of my boy's GSX (I gave them to him so he was really just returning them) and put them in my car. Old plugs were fouled to shit.
11:30 we're finally strapped in and ready to make the first pull (I was scheduled for 11 am but they were being real relax which is fine by me).
Zeroed the settings out for the baseline.....0 fuel across the board and 0 degrees of advance. Car had 5 gallons or more of c16 inside. Boost was 25psi falling ot 20 or so. First run netted a mind altering 266 front wheel horsepower and 290 foot lbs of torque.
Air fuel read off the chart, as in richer than 10:1. Good, this left me a lot of room.
So I get the air fuel to 12:1 across the board and this nets me 295 or so horsepower, 307 foot lbs of torque. Or something close to that.
Let it sit a while to cool down and then start increasing timing. I was getting 16 degrees at 7k rpm, and I wanted more like 23. So a few degrees here and there as well as a lot of cool down time and we're left with my final two pulls:
power 318.76 - torque 333.99
power 320.29 - torque 323.42
Appears that Scott is the winner of the pool. He guess 318 which was closest without going over. Jason's 321 was a very good guess.
Seriously, I could have done a run or two more and made more power....let it cool down some and advanced timing even a bit more (I was peaking at 21 degrees) but 320 is what I'd been telling people and so that seemed like a good place to stop. My goals as far as horsepower have been met and I will now need to get some traction and driving done.
Scott, I'm not sure where you're at right now but if and when you want to take it for a spin let me know....I'll put some C16 in the car.
-T
- JackoliciousLegs - 08-03-2004
hoh damn... scott's gonna be HAPPEEEEEEE
- Sijray21 - 08-03-2004
nice pulls!!!
and great tuning. Missed it by .7 whp, damnit!
you have approximately 178.79 more whp and 222.52 more wft*lbs than i do
hock: ....then depression sets in..... 
lol, nice pulls
scott, ur a lucky man
- KPWSerpiente - 08-03-2004
![[Image: dyno1.jpg]](http://gladstone.uoregon.edu/~gvidas/photos/car/dyno1.jpg)
Strapping it down
![[Image: travis.jpg]](http://gladstone.uoregon.edu/~gvidas/photos/car/travis.jpg)
Making critical adjustments
![[Image: outside1.jpg]](http://gladstone.uoregon.edu/~gvidas/photos/car/outside1.jpg)
Heading out after a hard hour on the dyno
![[Image: dynosheet.jpg]](http://gladstone.uoregon.edu/~gvidas/photos/car/dynosheet.jpg)
And of course.....this is all just talk without the sheet. Run 1 is baseline, number 11 is the best torque I got and run 10 is the 320 wheel horsepower pull.
-T
- Mike - 08-03-2004
hehe i originally said 320 then chaged to the "plus one to whatever" as a joke. woot!
not bad numbers... was the baseline what you came in with? i'm not familiar w/ dyno terminology.
- Sijray21 - 08-03-2004
MichaelJComputer Wrote:hehe i originally said 320 then chaged to the "plus one to whatever" as a joke. woot!
not bad numbers... was the baseline what you came in with? i'm not familiar w/ dyno terminology.
KPWSerpiente Wrote:Zeroed the settings out for the baseline.....0 fuel across the board and 0 degrees of advance. Car had 5 gallons or more of c16 inside. Boost was 25psi falling ot 20 or so. First run netted a mind altering 266 front wheel horsepower and 290 foot lbs of torque.
-T
that's a ton from the baseline imo, but i don't know much about b00st...
- Dave - 08-03-2004
good job Travis. I gotta get you driving so I can make some money off your ass. Race warz is where you'll do it!
Dammit, now I feel slow.
- Sijray21 - 08-03-2004
Dave Wrote:Dammit, now I feel slow.
you feel slow...shuddap, you and ur damn supra
how 'bout you and me trade cars for a while :wink:
actually i think we all feel slow now...THANKS Travis... :roll: , lol j/k
- .RJ - 08-03-2004
Jay's just bitter because his cibbic got dusted at a stoplight by the lunchbox.
- Sijray21 - 08-03-2004
.RJ Wrote:Jay's just bitter because his cibbic got dusted at a stoplight by the lunchbox.
fucker.....
i have 100.9 wft*lbs of torque...i'm bitter about everything
no small azian penis jokes either
scotty...nothing needs to be said about the dualee either so keep your mouth shut and your fingers still...
- .RJ - 08-03-2004
Damn, you just own3d yo'self...
*cracks beer*
*puts feet up*
- Feersty - 08-03-2004
Travis do you have the most hp in MM?
- Mike - 08-03-2004
Feersty Wrote:Travis do you have the most hp in MM?
Chad might...
- Dave - 08-03-2004
we should do an MM dyno day and settle that one.
Let's wait till after I do my engine swap though please :twisted:
- Feersty - 08-03-2004
Dave Wrote:we should do an MM dyno day and settle that one.
Let's wait till after I do my engine swap though please :twisted:
Haha. and what type of engine swap might this be Dave?
- CaptainHenreh - 08-03-2004
I said 315...so who's the winnar?
- Feersty - 08-03-2004
CaptainHenreh Wrote:I said 315...so who's the winnar?
Scotty Bradford